Call: 01752 415884

Covering Devon & Cornwall:

16 Daws Court

Old Ferry Road



PL12 6JD


Mobile: 07904 418682

Curing Methods

There are a series of curing methods available across the industry, ranging from ambient cure systems using simple thermosetting resins to extremely technologically advanced curing methods using LED and UV Light.

All catered for by your drainage specialists.

Ambient Cure

Ambient Cure is the method used to cure small diameter lining works in short lengths. The process requires minimal equipment for the installation of liners and the contractor benefits from relatively small set up costs coupled with a small installation footprint.

Ambient cure resins are used in short drag in and inversion liners and patch repair systems. The process usually involves using a simple 2 or 3 part resin system that begins to cure as soon as the components come into contact with each other.

The processes benefits the client as they are extremely cost effective, and generally reasonably user friendly.

The mechanical properties of ambient cure resins are generally not as good as their Hot Cure of UV Cure alternatives. The products are also limited to the length of repair that is possible due to the nature of the working time available with ambient cure thermosetting resins. 

We offer ambient cure variants of polyester, epoxy and silicate products. 

To speed up the cure of ambient cure systems and achieve greater mechanical properties, it is possible to introduce warm water to the system through use of a hot box, this is particularly useful when meeting tight timescales and also to minimise the risk of premature cure, the use of warm curing enables the operative to reduce the use of accelerator and catalyst to get the liner into the ground safely but achieve a cure in the same period of time. 


Extremely cost effective

User friendly

Small installation footprint


The mechanical properties are not as good as it's competitors

Hot Cure

The hot cure process utilises a steam or hot water boiler, usually in combination with a liner designed for inversion and coated with polyurethane or polypropylene for heat resistance.

Hot cure or steam cure is the industry standard working process for large diameter CIPP rehabilitation.


The liner is impregnated with a long pot life thermosetting resin system, usually polyester, vinylester or epoxy system is used. Each of which have varying characteristics, but all offering greater strength characteristics and working times than their ambient cure counterparts. 

Dependant on the resin type chosen, up to 500 metres can be installed in one application should the site layout allow. The process also involves a minimal site footprint relative to the repair that is being undertaken. The system is extremely flexible, liners and resins can be tailored to most CIPP applications.

Compared to ambient cure methods, the plant investments to successfully install hot cure or steam cure liners can be extremely costly. The process also requires potentially large amounts of water that need to be disposed of in accordance with the local water authority guidelines following installations. 

Liner lengths are also limited by the drainage layout and drag factor to be calculated in the inversion procedure. 


500m can be installed in one length.

Flexible system tailored to most scenarios.

Small installation footprint.


Costly equipment investment.

Large amounts of water to be disposed of.

UV Cure

UV CIPP can be utilised in most pipe profiles up to 1200mm diameter. With the latest technology UV Liners are winched into placed and inflated using a blower system, the UV/ LED light train is then pulled through the liner whilst it is in place and the liner is cured at speeds of up to 3 metres per minute.

The system is particularly beneficial to the client as there is reasonably flexible implementation, a short curing time and no water required for the installation. The system is also completely contained, and thus there is minimal environmental or human impact from each installation.

The main drawback for this system is the investment required for a UV equipment.

RSM is currently in the process of revolutionising the UV market, working in partnership with Applied Felts developing a needle felt UV system, and also a glass infused needle felt UV system.

For laminates up to 8mm a standard UV cure is sufficient to give excellent cured composite strength, for thicker laminates we utilise the standard UV with the addition of a thermal curing agent to prolong the post cure and give the best possible mechanical properties.


Short curing times, up to 3m per minute.

Minimum environmental and human impact.

Small installation footprint.


Costly equipment investment.

Liners require 2 access points for installation.

Limited applicability to layouts with bends/ displaced joints.